Page 46 - Charles G.G. Schmidt
P. 46

 COMPRESSION SPIRALS
Our Solid Carbide Spirals are made from High Quality Micro-grain carbide to give optimum performance in all materials Choose the proper cutting geometry by using the chart below. We have a bit for you. Made in USA.
• UPCUT - Designed for routing, grooving and slotting in both hard and soft woods, plastics, nonporous material, and composites.
Use when bottom  nish is important, and part hold down is not an issue. Creates an upward chip removal.
• DOWNCUT - Designed to hold material down during templating and thru cutting. Intended to eliminate or reduce chipping on
the top edge. Helps hold parts to table during cutting.
• COMPRESSION - Spiral bit with an up and down cutting edge. Designed to produce a chip free  nish on the top and bottom
in solid wood, wood composites, veneer and laminated materials.
• MORTISE COMPRESSION - Compression bit with a shorter upcut. Designed to produce mortise and dado cuts when top  nish is important.
• CHIPBREAKER - Designed to produce a good  nish, while allowing for faster feed rates.
• ROUGHER - Designed to allow for extremely fast hogging in solid wood and wood composites. Not designed to produce  nish
cuts, in most applications.
• LAMINATE GRADE - Designed for extended tool life in MDF, especially with single or double sided laminate  nishes.
•
CHIPLOAD = Feed Rate RPM = Feed Rate
(RPM X NO. Flutes) (NO. Flutes X ChipLoad)
Feed Rate = NO. Flutes X RPM X ChipLoad
COMPRESSION SPIRALS
  RCC1236
RCC1414
SINGLE FLUTE
Designed to cut double sided laminated or veneered material to achieve an excellent  nish on both top and bottom edges. Use a single  ute tool for slow to moderate
feed rates.
DOUBLE FLUTE
Use a double  ute tool for middle of the road standard feed rates to achieve an excellent  nish
THREE FLUTE
Where the fastest feed rate is needed and still get an excellent  nished edge on both top and bottom.
           CAT. NO.
Cutting Diameter
Cutting Length
Shank Diameter
Overall Length
        One Flute Compression Spirals
       1/4"
7/8"
1/4"
2-1/2"
       RCC1304
RCC1354
3/8"
1"
3/8"
3"
       1/2"
1-1/4"
1/2"
3"
       RCC1364
1/2"
1-5/8"
1/2"
3-1/2"
       5/8"
2"
5/8"
4"
        RCC1454
3/4"
2"
3/4"
4"
       Two Flute Compression Spirals
       RCC2236
1/4"
7/8"
1/4"
2-12"
       RCC2238
1/4"
1"
1/4"
2-1/2"
            RCC2310
3/8"
1-1/4"
3/8"
3"
           RCC2352
1/2"
1-1/8"
1/2"
3"
       RCC2354
1/2"
1-1/4"
1/2"
3"
       RCC2360
1/2"
1-3/8"
1/2"
3"
       RCC2362
1/2"
1-3/8"
1/2"
3-1/2"
        RCC2364
1/2"
1-5/8"
1/2"
3-1/2"
       RCC2368
1/2"
1-7/8"
1/2"
4"
       RCC2372
1/2"
2-1/8"
1/2"
4"
       RCC2410
5/8"
1-5/8"
5/8"
3-1/2"
       RCC2414
5/8"
2"
5/8"
4"
       RCC2454
3/4"
2"
3/4"
4"
        RCC2456
RCC3310
RCC3360
3/4"
2-1/2"
3/4"
5"
       Three Flute Compression Spirals
       3/8"
1-1/4"
3/8"
3"
       RCC3354
1/2"
1-1/4"
1/2"
3"
       1/2"
1-3/8"
1/2"
3"
       RCC3364
1/2"
1-5/8"
1/2"
3-1/2"
       RCC3414
5/8"
2"
5/8"
4"
           RCC3454
3/4"
2"
3/4"
4"
      44
To Place An Order Call: 1-800-SCHMIDT 800-724-6438 www.cggschmidt.com
SOLID CARBIDE ROUTER BITS
 
   44   45   46   47   48