Page 47 - Charles G.G. Schmidt
P. 47

                  CAT. NO. Upcut
RCU2236
CAT. NO. Downcut
Cutting Diameter
Cutting Length
Shank Diameter
Overall Length
        One Flute Upcut / Downcut Spirals
        RCU1238
RCD1238
1/4"
1"
1/4"
2-1/2"
        RCU1262
RCD1262
5/16"
1"
5/16"
3"
        RCU1304
RCD1304
3/8"
1"
3/8"
3"
        RCU1362
RCD1362
1/2"
1-3/8"
1/2"
3-1/2"
        Two Flute Upcut/Downcut Spirals
        RCU2172
RCD2172
1/8"
1/2"
1/4"
2"
        RCU2190
RCD2190
5/32"
1/2"
1/4"
2"
        RCU2204
RCD2204
3/16"
3/4"
1/4"
2"
        RCU2222
RCD2222
7/32"
3/4"
1/4"
2-1/2"
        RCD2236
1/4"
7/8"
1/4"
2-1/2"
        RCU2238
RCD2238
1/4"
1"
1/4"
2-1/2"
        RCU2240
RCD2240
1/4"
1-1/4"
1/4"
2-1/2"
        RCU2262
RCD2262
5/16"
1"
5/16"
3"
        RCU2264
RCD2264
5/16"
1-1/4"
5/16"
3"
        RCU2304
RCD2304
3/8"
1"
3/8"
3"
        RCU2306
RCD2306
3/8"
1-1/8"
3/8"
3"
        RCU2310
RCD2310
3/8"
1-1/4"
3/8"
3"
        RCU2312
RCD2312
3/8"
1-1/4"
1/2"
3"
        RCU2332
RCD2332
7/16"
1"
1/2"
3"
        RCU2334
RCD2334
7/16"
1-1/4"
1/2"
3"
        RCU2354
RCD2354
1/2"
1-1/4"
1/2"
3"
        RCU2364
RCU2372
RCD2364
1/2"
1-5/8"
1/2"
3-1/2"
        RCU2370
RCD2370
1/2"
2"
1/2"
4"
        RCD2372
1/2"
2-1/8"
1/2"
4"
        RCU2390
RCD2390
17/32"
1"
1/2"
3"
        RCU2410
RCD2410
5/8"
1-5/8"
5/8"
3-1/2"
        RCU2414
RCD2414
5/8"
2"
5/8"
4"
        RCU2450
RCD2450
3/4"
1-1/2"
3/4"
4"
        RCU2454
RCD2454
3/4"
2"
3/4"
4"
        RCU2460
RCD2460
3/4"
3"
3/4"
6"
        RCU2462
RCD2462
3/4"
3-1/2"
3/4"
6"
        Three Flute Upcut/Downcut Spirals
        RCU3234
RCD3234
1/4"
3/4"
1/4"
2-1/2"
        RCU3310
RCD3310
3/8"
1-1/4"
3/8"
3"
        RCU3354
RCD3354
1/2"
1-1/4"
1/2"
3"
        RCU3366
RCU3370
RCD3366
1/2"
1-5/8"
1/2"
4"
        RCD3370
1/2"
2"
1/2"
4"
        RCU3410
RCD3410
5/8"
1-5/8"
5/8"
3-1/2"
        RCU3414
RCD3414
5/8"
2"
5/8"
4"
        RCU3450
RCD3450
3/4"
1-1/2"
3/4"
4"
        RCU3454
RCD3454
3/4"
2"
3/4"
4"
        RCU3460
RCD3460
3/4"
3"
3/4"
6"
             RCU3462
RCD3462
3/4"
3-1/2"
3/4"
6"
      Technical Assistance & Inquiries: 1-201-391-5300 FAX: 1-201-391-3565
 45
SOLID CARBIDE ROUTER BITS
 UPCUT AND DOWNCUT SPIRALS
   UPCUT SPIRAL
Manufactured to cut solid wood, wood composites and some plastics, these tools are used where an upward chip removal is required and an excellent  nish on bottom edge is needed. Additional hold down pressure is required for faster, more aggressive
feed rates
 DOWNCUT SPIRAL
Three  ute downcut spirals are used for a
high feed rate applications and excellent, smooth  nish on the top edge.
SHARPENING: Sharpening services available at a fraction of the cost of new bits.
 Note: Not all sizes listed
 
   45   46   47   48   49